Battery Cost per Kilowatt-Hour Calculator

Estimate the upfront battery and installation cost per usable kilowatt-hour. Capacity is calculated from nominal voltage and amp-hour rating; the usable percentage is an illustrative assumption. Actual usable energy varies with discharge rate, temperature, battery condition, and voltage. This estimate does not include charging costs or battery cycle life.

Battery Backup Sizing Calculator

Estimate the nominal battery capacity needed to run a specified average electrical load for a chosen backup time. Enter the battery bank voltage, usable depth of discharge, conversion efficiency, and reserve appropriate to your setup. Defaults are illustrative. The estimate assumes a constant average load; actual runtime varies with battery condition, discharge rate, temperature, and equipment losses. If purchasing individual batteries, divide the result by the capacity of a correctly configured battery bank and round up to a whole number of compatible banks.

Battery Usable Capacity Calculator

Estimate usable energy from a battery’s rated amp-hour capacity and nominal voltage, using your assumed usable capacity window and delivery efficiency. Defaults are illustrative; actual capacity varies with discharge rate, temperature, battery condition, and equipment.

Battery Storage Efficiency Calculator

Estimate round-trip battery storage efficiency by comparing usable energy discharged with energy used to charge the battery. Measure both at the same system boundary over a complete charge and discharge cycle. Defaults are illustrative; results depend on operating conditions and measurement accuracy.

Battery Energy Density Calculator

Estimate gravimetric energy density from nominal voltage, rated capacity, and battery mass. This calculation uses nominal electrical energy and does not account for discharge conditions, voltage variation, or usable capacity.

Inverter Battery Runtime Calculator

Estimate inverter runtime from battery voltage, capacity, allowable depth of discharge, inverter efficiency, and connected load. Defaults are illustrative. Actual runtime varies with battery condition, discharge rate, temperature, and changing loads.

Solar Battery Charging Time Calculator

Estimate the peak-sun hours needed to replace a specified share of a battery’s capacity. The calculation uses nominal battery energy and an overall charging efficiency; actual time varies with sunlight, panel output, temperature, charge-controller limits, and battery charging behavior. Defaults are illustrative.

DC to DC Charger Time Calculator

Estimate charging time from battery capacity, starting and target state of charge, charger output, and an assumed charging efficiency. The estimate uses a constant average charging rate; tapering, temperature, loads, and battery management limits can change actual time. A target at or below the starting charge gives zero hours. Defaults are illustrative.

Dual Battery Runtime Calculator

Estimate how long two batteries can power a steady load using their combined nominal energy, a chosen usable capacity, and system efficiency. Use batteries with the same nominal voltage and enter the load’s average power. The estimate excludes battery aging, temperature effects, and capacity loss at high discharge rates.

Trolling Motor Battery Runtime Calculator

Estimate runtime from battery capacity, the number of batteries connected in parallel, usable capacity, and the motor’s average current draw. Use the battery bank’s amp-hour rating and an average draw appropriate to your operating speed. Batteries connected in series increase voltage, not amp-hour capacity; enter one for a single series string. Actual runtime varies with speed, battery condition, temperature, and discharge rate.

Marine Battery Runtime Calculator

Estimate runtime from battery capacity, nominal voltage, usable depth of discharge, system efficiency, and continuous load. Defaults are illustrative. Actual runtime varies with battery chemistry, discharge rate, temperature, battery age, and changing loads; check the battery manufacturer’s specifications.

RV Battery Size Calculator

Estimate the nominal battery bank capacity needed for your RV from daily energy use, days between charging, battery voltage, usable capacity, and system efficiency. Defaults are illustrative. Round up when choosing batteries and check that their voltage and capacity suit your system.

Dash Cam Parking Mode Runtime Calculator

Estimate parking mode runtime from battery capacity, nominal voltage, the percentage of capacity available before the cutoff, dash cam power draw, and an efficiency allowance. Defaults are illustrative. Actual runtime varies with battery health, temperature, other vehicle loads, and the voltage cutoff; the available capacity input should reflect the manufacturer’s specifications and your cutoff settings.

Car Fridge Battery Runtime Calculator

Estimate how long a battery can power a car fridge without charging. Enter the battery’s nominal capacity and voltage, your chosen usable capacity, and the fridge’s running power and estimated duty cycle. The result is an approximation: compressor cycling, temperature, battery condition, and other loads affect actual runtime. Defaults are illustrative assumptions.

Portable Jump Starter Runtime Calculator

Estimate how long a portable jump starter can power a device using its battery capacity, device power draw, conversion efficiency, and desired reserve. Enter the battery’s manufacturer-rated capacity in watt-hours and the device’s average power draw in watts. Actual runtime varies with battery age, temperature, output voltage, and changing power demand. This estimate applies to powering accessories, not the number of engine starts.

Car Jump Starter Capacity Calculator

Estimate the usable battery energy needed for a planned number of starting attempts. Enter the expected cranking current and voltage, duration, and an assumed energy delivery efficiency. Defaults are illustrative. This energy estimate does not establish whether a jump starter can supply the required starting current; check its manufacturer-rated current, vehicle compatibility, and operating conditions separately.

Starter Motor Current Calculator

Estimate starter motor current from mechanical output power, operating voltage, and motor efficiency. Enter voltage measured or expected during cranking. Defaults are illustrative; actual current changes with load, temperature, and battery voltage.

LiFePO4 Battery Charging Time Calculator

Estimate charging time from battery capacity, starting and target state of charge, charger current, and an assumed charging efficiency. The efficiency allowance approximates charging losses and current taper; actual time depends on the charger, battery management system, and conditions. If the target is at or below the starting charge, the estimate is zero.

AGM Battery Charging Time Calculator

Estimate AGM battery charging time from its capacity, current state of charge, charger current, and assumed average charging rate. The estimate accounts for reduced current during the final charging stage and other losses.

Lithium Battery Runtime Calculator

Estimate runtime from battery capacity, nominal voltage, usable capacity, load power, and system efficiency. Defaults are illustrative. Actual runtime varies with load, temperature, battery condition, and discharge rate.

Lead Acid Battery Runtime Calculator

Estimate runtime for a constant-power load using the battery’s rated capacity and Peukert exponent. Defaults are illustrative; actual runtime varies with battery condition, temperature, discharge rate, and other losses.

Battery Cycle Life Cost Calculator

Estimate battery purchase cost per kilowatt-hour delivered over its cycle life. Enter the rated cycle life at the selected depth of discharge; use a round-trip efficiency assumption appropriate to your battery and charging system. This simplified estimate assumes consistent cycling and excludes charging electricity, maintenance, replacement labor, and capacity fade. Defaults are illustrative.

Battery Depth of Discharge Calculator

Calculate the percentage of a battery’s rated capacity used between two charge measurements. Enter capacity and charge amounts in amp-hours (Ah). Remaining charge must not exceed starting charge, and neither charge amount should exceed rated capacity. The default values are illustrative; actual available capacity varies with conditions and battery age.

Battery Discharge Rate Calculator

Calculate a battery’s discharge rate in C from its load current and rated capacity. This estimate assumes a constant current and uses the battery’s stated amp-hour capacity; actual capacity and runtime vary with discharge conditions, temperature, age, and battery chemistry. Defaults are illustrative.

Battery Bank Energy Calculator

Estimate usable battery bank energy from the nominal voltage and capacity of one battery, the number of batteries, the chosen depth of discharge, and system efficiency. Batteries are assumed to be identical; series and parallel connections preserve the same total nominal energy. Actual usable energy varies with discharge rate, temperature, battery condition, and manufacturer limits. Defaults are illustrative assumptions.

Parallel Battery Capacity Calculator

Add the rated capacities of up to three compatible batteries connected in parallel. Enter 0 for an unused battery. The result is the ideal combined capacity in amp-hours; parallel connections retain the same nominal voltage. Actual usable capacity varies with battery condition, discharge rate, and system losses. Default values are illustrative.

Battery Series Voltage Calculator

Estimate the total voltage of identical batteries connected in series. Series voltages add; use the voltage measured or specified for each battery. This assumes all batteries have the same voltage and are connected in the same direction. Actual voltage varies with charge and load.

Car Battery Charger Size Calculator

Estimate the average charger output needed to replenish a battery within a target time. Defaults are illustrative. Actual charging slows near full charge, so allow extra time and follow the battery manufacturer’s charging-current limits. Choose a charger rated at or above the calculated output, within those limits.

Battery Cable Voltage Drop Calculator

Estimate voltage lost across a battery cable circuit using conductor resistivity. Enter the one-way cable length; the calculation assumes an equal-length return conductor and resistivity at approximately 20°C. Connections, temperature changes, and chassis-return resistance are not included. Defaults are illustrative.